Showing posts with label Cockpit area. Show all posts
Showing posts with label Cockpit area. Show all posts

Friday, 29 November 2013

Steering Column finishing

Spent ages sorting and getting the steering column finally fitted, liking the look of it and had to fit the Moto Lita wheel to see how it all looked. Just a pity the Vectra one has to be fitted for the IVA test.
Liking the look of the GD stalks when its all put together.
The dash switches got the decals applied today as well, Fog light, light and heater fan plus the hazard warning light symbol.


Pic below is wheel just on the splines but not bolted right down.


Now with the not so cool IVA steering wheel :(


Next on the to do list is to sort out some IVA issues in the interior before bolting the seats in.



Sunday, 24 November 2013

Control stalks

The steering column area got a wee bit done on it today as well, the stainless cover I have for the front face of the steering column has symbols engraved on it so Andy said the stainless stalks could be fitted before the IVA test. First was to run the hacksaw through the plastic stalk just before the flange where the rubber boot sits over.



In the picture above you can see the exact place the stalk is cut and filled. Once thats done a small pilot hole was drilled in the center of the shaft then a 5mm drill used to drill down the stalk. The length that the stalk is drilled is the amount that your GD stainless stalks are threaded.


Once drilled and tapped with a M6 x 1.0mm tap the stainless stalk is then screwed in. I applied some thread luck or nut retainer medium grade when doing this.



Dash

I got pulled away from the car for most of this week as work just went mental and was working all hours over the past 5 days to get on top of things so I could get back to the important job again :)
The build is coming along nicely now and getting to the stage where I need to really forward plan on small silly bits or jobs just cant be completed.
With all the wiring in the dash area out of the way for the IVA it was time to start getting the dash mounted, unlike the leather covered dash the carbon dash has to have bolts secured to the back of the dash as bolting though the dash would look a tad naff even with button heads.
Some strips of stainless was cut for the 4 mounting bolts and then drilled with a 6.5mm hole in the center, the bolts were then put through the flat strips and welded.


Pic is a bit poor but shows the job, Next was to mix up some fiberfill repair paste and put a blob on the back of the dash. The mounting bolt was then pushed onto it and more paste added to cover the securing bolt. One thing for sure it isnt going to vibrate off.

Once the bolts had set a corresponding hole was then marked and drilled in the body. I used some marked paint on the ends of the bolts to mark the dash and drilled the holes. As the dash is presented at an angle due to the bottom lip of the dash the dremmel was then used to elongate the holes down slightly to get the dash to fit snugly into place.



Dash fitting now though the bottom alloy plates have to be sorted to fit properly yet.


Wednesday, 9 November 2011

heater and dash under trays

Time for a wee update though not a lot of progress that can been seen really. As I started working on the wiring and metering out wires etc. I realised that i needed to really get the heater ducting and lower vents finished in order to see what space I had where for cables and other things. To do this I needed to get the under trays fitted.
The under trays need set into place then held at the front with clamps whilst the back is marked then drilled through and on up into the steering column support bar in a few places, then tapped. The right and left trays need this done, the center one has holes in the 2 supports already and just the tray needs drilled.
The fronts of the trays that fit either side will get held in place with the dash lip as it has to be bolted underneath.


With the rear mounting holes done, The 76mm hole was cut with the holesaw for the adjustable heater duct and also a 12v power socket was added as well, This was done for both the passenger and the drivers side.




On the passenger side I also added a bank of relays as I needed extra on the car that wasnt covered by the GD loom. I need 1 for the fuel pump, 1 for firing the 2nd cooling fan as I'm using 2 stage cooling from the GM ECU, 2 more relays are required for the heaters in the drivers and passenger seats. I also need one more for part of the alarm system. The last one at the moment is spare, it will either stay a spare or its always there just encase or an emergency if required to swop with another.






Not loads of room with all the heater hoses on the passenger side along with the wiper motor.





Above pic shows the T piece which splits the air to the demist on the dash and also the lower hot ait vent. next hmmmmmm more wiring in the dash area :)

Sunday, 6 November 2011

Wiper motor and cockpit wiring

Time to get the wiper motor and drive mech into place, first the motor was bolted onto the bracket and the drive and tube curved across the dash past the 2 wiper spindle mechs.
Once everying was in place correctly I marked the bundy tube where the cuts had to be made and also running it about 100mm past the 2nd wiper spindle. Removed the whole lot again and cut the tube pieces and flared all the ends with my flaring tool. All put back and bolted into place. Will have to check operation at some point once the electrics are sorted to make sure its parking in the right place and not 180deg out.









With the wiper motor in place I bolted in the dash air vents then set about looking at piping the dash vents and the vents that blow the air down towards the footwells, The pipes need to be split and I had seen before where people made up T pieces etc. I got a handlier way around this and its a perfect fit for the flexi tubing :) I used 2 waste T pieces and cut of the ends where the rubber O rings are housed the remaining pipe is the excact diameter required. No particular reason I painted them balck the same colour as the pipe. I 'll get back to finishing this job at a later date.
Also got stuck into the wiring behind the dash, I ran near ll the cables that i could behind the dash and inside the car so quite a bit of work in this area, will take me a while and my head is pickled for today :).








Tuesday, 1 November 2011

Door trim etc

Decided to get the drivers side door finishers, eschusions etc sorted, also added the Carbon kick plate. Made a start on the fitting the steering column, first was to get it lined up and cut as slot where the bolt wil pass through.











Monday, 31 October 2011

Pedal box

What started out to be smallish job ended up taking a long time to do. I thought I was at the point of adding the brake pedal switch and then simply bolting the pedal box back in, hmmmmm wrong, quite a few hours later with the pedal box in and out a few times and a sore back its in now and I hope it don't have to come out for a long time.
Once I made the bracket for the brake light switch I ran some rubber U channel around it, not sure if its needed for IVA or not but better safe than sorry. Once I put the pedal box back in I looked at the spacings of the pedals and remembered that for people with broader feet needs the pedal spacing tweaked. As I had the footwell extension in I could move the clutch and brake pedals over towards the tunnel, I also moved the acceleration pedal at tad. I ended up with the pedal box in and out a few times to get this right for me and taking it apart each time to alter the pedals in the vice. Not easy putting the pedal box in on ur on bolt wise. I thought once this was done that was me , errr em nope, I noticed the goo goo pedal :) was just a straight bar right up and nothing there to attach the throttle cable to, suppose this is due to the fact we fit so many engines/cables. I had to take a while and figure out the route the throttle cable needed to go from the engine back to the pedal. Took a while to get the best route but once it was attached to the bulkhead wall I could see what mods needed carried out on the pedal shaft to attach the cable. I drilled and slotted the top and then added a stainless Jubilee so it could never jump out of the locator.
Pedal box was then bolted up and during this the adjusters were set for the brake and clutch cylinders, just more time :)
On another note I removed the windscreen pillar cover and ran some rubber U channel around it, again for IVA and their edge rule, I also replaced the lower bolt for a dome head again just to be safe. Some pics below, not sure what I'm doing next but loads to choose from :)

                                                                  Pedals moved to the left
                                                              Plenty of foot room now :)
All bolted up and throttle connected, rubber around windscreen pillar cover.
                                            Stainless throttle bracket added and cable attached



Sunday, 30 October 2011

Footwell extension and carpets

I started on the car today by taking back out the drivers seat and making a start on the handbrake mounting position and getting the mounting holes drilled through the carpets and body floor. I need to get my handbrake cable shortened and a different end put on it. Will ring speedy cables tmw and hopefully that will get that snag sorted.
I went to do the drivers side bulkhead carpet then realised I had not fitted the footwell extension, worse still I had not drilled all the holes in the body to get it bolted up. Well this took ages to do but we got there in the end. I put alloy rivnuts in the extension piece and used 5mm button heads inserted from the inside. I also run a bead of  silicon to help seal it.
Once the extension piece was installed next began trying to carpet round the extension and the last bit of the tunnel, hmmmmmm pain in the butt this was and I was getting a tad high with my head right inside the footwell lol.
I also glued in the small bulkhead piece once i cut the holes out for the pedal box.
Before the pedal box goes back in I need to make a brake switch bracket to mount on the pedal box that's the next job on the to do list.


Saturday, 29 October 2011

Seats and Harness

Started off the day by tidying the workshop as I hate tools lying everywhere and then i cant find anything.  Finished of all the harness anchor points first then started into the seat adjusters. I fitted them to the seats before drilling the holes in the shell for mounting the seats in. All bolted in so thats a bit more done and dusted for now. Tmw's another day :)













Friday, 28 October 2011

Roll bars and interior

Got back to doing the final mounting on the roll bars. The rubber seals i made up were stuck to the boot floor with sikaflex. I drilled and tapped the rear leg of the roll bars to allow fitting of the new head rest mounts. I got some stainless steel thread bar to allow mounting to the headrest.
Took a while to get the hoops into place and everything bolted up, Job done now :)
I set the seats in the car to see what the interior was going to look like, looks the mutts nutts :))) well happy with the design of the seats I come up with, red stitching looks well on them.
Hope to get a bit more done over the weekend, some pics below of the work done and car now.













Friday, 21 October 2011

Interior leather

Needed to make up a few stainless brackets to bolt the tunnel leather top on, I measured quite a few times before cutting the 100mm hole for the gear lever. The gaitor i spent a bit of time on, firstly getting it so the eschusion screws went through the leather as well and I also added some contact adhesive between the eschusion and leather then used a few bolts to secure it to the tunnel top until it set.  The stainless tabs are ready to be bent around the tunnel and screwed on.
Working on the interior carpet tmw and trim, I'm hoping to have all the carpet fitted by Sunday. Pedal box is removed ready for the bulkhead piece on the drivers side next.







Thursday, 20 October 2011

Door cards etc

Got both the door cards fitted, they were simple enough to do just needing 7mm holes marked out and drilled for the door card clips and a nick in the leather for the handle to be fitted.

Made a start on the interior carpet doing a dry run, more on this on the next update, I made up some temp head rest brackets as I,m getting some different one made up by GD that connect to the rear leg of the roll bar.

Another job that need done was to make up some rubber seals where the roll bar legs go through the floor of the boot to stop any ingress of water, I can't final fit the hoops yet until I mark out then drill and tap the holes in the rear leg where the final rest rest brackets will be fixed. Once they are done thats the hoops hopefully ready to be properly fitted.



Got some rubber U channel and fitted it to the inner lip of the boot, makes a nice tidy finish to the area, I still need to get some rubber seal and fit it around the boot as well to stop any water getting in.



Tackling a few other bits on the interior at the moment will post more on the next update, thats all for now, theres work to be done :)

Sunday, 16 October 2011

Interior

I started of the day by making a small list of some bits I needed and then finished in the boot for now. I need to sand and buff the back of the car again as there is a few wee scrapes and much easier before I fit the roll hoops again.
Anyways the inside of the car had been neglected so far with pretty much nothing done, first the floor got painted just to tidy it up, I know its covered with carpet but it looks better for now.


With that done one of the door cards was tackled next it wasnt that hard with the clips in the door cards to transpose the marks onto the door for drilling the 7mm locator holes.



Looks pretty good and makes the car look a little further on.
Next I started to look at the side carpets etc then realised the ridge around the door needed trimmed back to 12mm ,grrrrrrrrrrrrr I thought I had all the dusty fiberglass cutting jobs done, anyways I marked a line right around both doors with the scriber and cut and sanded the lip to 12mm.
Onto the Centre carpet I got it out to see what way it fitted and tried to figure out what way to put it down and also mark where to cut it for the gear lever.
I ordered eschusions from GD as well to tidy up the opening in the body for the door hindges, these come flat and laser cut, part of them needs bent 90 deg before fitting.


 Once the 4 eschusons were bent the tape was peeled of them and give them a quick polish before fitting to the passenger side. Drivers side will get done at a later date.